POLYWATER P7-12 16-Oz Type P7 Aerosol (net wt 10 oz) 02786804100 Case OF 12

Product Description

AMERICAN POLYWATER P7-12 16-Oz Type P7™ Aerosol (net wt 10 oz) 02786804100 Case OF 12 P7™ A Multi-Functional Penetrating Oil for Industrial and Electrical Use 7™ Penetrating Oil is suitable for all kinds of electrical and industrial uses. P7™ Oil cleans dirt and grime, loosens rust and scale, and penetrates frozen parts. Use it to maintain and lubricate equipment. P7™ Penetrating Oil is multi-functional. It cleans, penetrates, and lubricates to extend equipment life. P7™ Oil also acts as a moisture displacer and corrosion inhibitor. It drives out moisture and dries wet connections, leaving a protective film that is non-conductive. ADVANTAGES Lubricates Moving Parts Frees Stuck Parts Protects Against Rust and Corrosion Displaces Moisture Removes Grime and Rust Film is Non-Conductive Harmless to Most Plastics Safe on Metal, Paint, & Rubber Contains No CFC's or Chlorinated Solvents Silicone-Free Cleans Tar, Grease, Rust, and Adhesives PROPERTIES Flashpoint (ASTM D93) Initial Boiling Point Specific Gravity Dielectric Strength (ASTM D877) Relative Evaporation Rate Propellant USDA 100°F/38°C 245°F/118°C 0.69 13 KV Fast Hydrocarbon Approved PENETRATION & CLEANING P7™ Penetrating Oil cleans grease and tars and removes adhesives and rust. Other solvent cleaners are not necessary. P7™ Oil dissolves grit and grime contaminants, leaving behind a fine protective film. P7™ Penetrating Oil has a low surface tension, which allows it to spread into a very fine film. One 12-ounce can of P7™ Oil will cover approximately 300 square feet of surface. This low surface tension allows P7™ Oil to creep up surfaces against gravity. It will penetrate and coat 16mm of a threaded bolt in 15 minutes. P7™ Oil will lubricate tight crevices and loosen frozen parts. PROTECTION & CORROSION PREVENTION [Type P7® Penetrating oil loosens rust & scale, frees stuck parts, lubricates, displaces water & moisture, inhibits corrosion, cleans & protects metal] P7™ Penetrating Oil offers superior corrosion protection by leaving a non-conductive film. This long-lasting film increases service life. The photo at right shows the results of a three-week outdoor weathering test run on low carbon steel. The plates were sanded, cleaned, and saturated with various penetrating oils. The steel plates were left in the elements, untouched for three weeks. P7™ acts as a tough, protective barrier; the steel plate has no rusting or mottling at the conclusion of the test. LUBRICATION P7™ Penetrating Oil is an exceptional lubricant. The coefficient of friction can be determined using the Falex Pin and Vee Block Test Machine (ASTM D3233A). Load is applied to two V-blocks that press against a rotating steel journal immersed in the oil. The coefficient of friction value is derived from the torque measurement on the pin. The more the penetrating oil lubricates and lowers the torque, the lower the resulting coefficient of friction. Documented test results show that P7™ Oil has a significantly lower coefficient of friction than other commonly used penetrating oils. Extreme pressure testing using the Pin and Vee Block Test Machine confirms P7™ Oil's excellent performance under high loads. The test will run to a load force of over 1,000 pounds before failure. WATER DISPLACEMENT P7™ Penetrating Oil displaces moisture and dries out ignitions. It creeps under water and ice, dissolving and carrying away these contaminants. A non-conductive, protective film is left behind. P7™ Oil displaces water according to the procedure described in Mil-Spec C-16173E. No rusting or mottling was observed on the treated surface. COMPATIBILITY P7™ Penetrating Oil is compatible with most plastics and elastomers. Tables I and II show the effect of P7™ Oil on various plastics and rubbers. Testing is based on a soak test described in ASTM D543. P7™ Oil will temporarily affect some rubber compounds. These rubbers may swell, but should return to their original state after the solvent carrier has dried. Immersion will affect sensitive materials more than incidental contact of a spray and wipe. It is recommended that all plastic parts, gaskets, seals and O-rings be tested for specific use and exposure method. COMPATIBILITY WITH PLASTICS & ELASTOMERS TABLE I AGING 72 HOURS AT 50°C TYPE OF PLASTIC % WEIGHT CHANGE % THICKNESS CHANGE APPEARANCE ABS +0.04 +0.79 NC Acrylic -0.02 -0.04 NC CPE Thermoplastic +16.10 +4.27 NC CPE Thermoset +22.12 +20.99 SS Delrin® +0.17 +0.25 NC Epoxy -0.05 0 NC Nylon 101 -0.08 -1.57 NC Polycarbonate -0.03 -0.59 NC Phenolic +1.24 0 NC Polyethylene +14.19 +5.44 NC Polystyrene +13.85 -3.64 SF PVC +0.06 0 NC Teflon® +0.07 -0.25 NC Tygon® +4.95 0 NC Ultem® 1000 -0.08 -0.27 NC Valox® 420 +0.03 -1.11 NC TABLE II AGING 72 HOURS AT 50°C TYPE OF ELASTOMER % WEIGHT CHANGE % THICKNESS CHANGE APPEARANCE EPDM +149.56 +43.77 S Neoprene +26.64 +9.79 SS Nitrile +1.06 0 NC SBR +52.48 +14.36 S Silicone +48.04 +17.87 S Viton® +0.56 +0.26 NC KEY: NC=NO CHANGE Type P7™ is a trademark of American AMERICAN POLYWATER Corporation SF=SOFTENING Delrin® and Teflon® are trademarks of Du Pont SS=SLIGHT SWELLING Ultem® 1000 and Valox® 420 are trademarks of G.E. Plastics S=SWELLING Tygon® is a trademark of Norton Performance Plastics Viton® is a trademark of Du Pont Dow Elastomers USAGE DIRECTIONS Position nozzle 6 to 8 inches (15-20 cms) from surface and spray with light even strokes. Use extension tube for difficult to reach areas. Let P7™ Oil soak for several minutes to loosen rusted parts. Allow 4 to 6 hours to fully dry. P7™ Oil eaves a non-conductive, protective film. SAFETY P7™ Penetrating Oil has a low level of toxicity. Avoid breathing spray, mist, or vapor. As with any solvent, ventilation should be sufficient to keep vapors at safe levels. P7™ Penetrating Oil is combustible. Do not expose to fire or flame. Good industrial hygiene practice and appropriate precautions should be employed during use. STORAGE P7™ Penetrating Oil is classified as combustible. Keep containers cool, dry and away from sources of ignition and oxidizing materials. Do not expose aerosol cans to direct sunlight or temperatures above 120°F (50°C). Do not puncture or incinerate aerosol cans. Aerosol cans are freeze/thaw stable. This product has a shelf life of three years.